Free shipping is only valid on total purchases of $199 or more and ground shipments within the contiguous 48 states for products weighing less than 150 lbs. Special handling fees may be required for some products.Shipping fees will be added for all orders under $199 or that include oversized items or any item of 150 lbs or more. Please contact customer service if you have any questions.
Replacement parts and hardware for your hydraulic system will keep the cylinders and winches operating as they should on your wrecker or car carrier. Whether it’s a full hydraulic system or a small elbow fitting, count on Zip’s AW Direct to carry the parts you need to get back to work.
Electric Clutch used with Serpentine Belt for Clutch Pump Applications.
(Basic pump kits include: pump, idler pulley, clutch, serpentine belt, crankshaft pulley, pump mtg. Bracket's as needed.
Buyers Products R38D Series Control Cable with 5 Inch Travel features a
corrosion resistant stainless steel core to ensure long life. The cable has 5
in. of total travel with no neutral detent.
Can be easily customized by cutting conduit and core wire. It includes a small
clamp to secure the output end for added stability, and a 2 in. control knob.
Replacement 12 VDC electric clutch. Used for double v-belt applications with
the 326-9110-052 pump and other pumps with the tapered and keyed shafts.
NOTE TO INSTALLER
BURNISHING: Clutches will need a short burnishing period to generate the rated
torque. This is a process of cycling the clutch to slightly wear the friction
surfaces. This allows full contact and maximum magnetic attraction required for
rated torque (or more). TO AVOID BURNING OR HEAT DISTORTION, THE FOLLOWING
PROCEDURE IS RECOMMENDED: After clutch is installed, run at 1000-1200 RPM.
Cycle the clutch on/off at the rate of 10 seconds on - 10 seconds off for a
minimum of 50-100 cycles.
This Parker hydraulic pump has a fixed displacement gear pump for use with a
belt-driven electro-magnetic clutch, for Deweze clutch pump kit.
(Basic pump kits include: pump, idler pulley, clutch, serpentine belt, crankshaft pulley, pump mtg. Bracket's as needed.
This is a Parker 12 Gallon Per Minute Hydraulic Pump at 1600 RPMs. This is a
Parker PH14 "A" Mount Pump with a clockwise rotation. This pump features side
ports. This pump has a 7/8" tapered shaft with a woodruff keyway. This pump
will work with a Century 312 model wrecker.
The B/A Products hose splice repair kits are perfect for temporary repairs on
the roadside. These splice kits will allow the operator to load and unload
while avoiding costly road service repairs.
DewEze Clutch Pump Kit for the 2019-2024 Dodge trucks with a 6.7 liter diesel engine. The pump in this kit is rated for 9, 12, 17, 9HP and 12HP Gallons Per Minute of flow. It is run with a 6"- 8 grove serpentine belt. (Basic Pump Kits Include: pump, idler pulley, clutch, serpentine belt, crankshaft pulley, pump mtg. bracket)
This Hydraulic Clutch Pump has a fixed displacement gear pump for use
with a belt-driven electro-magnetic clutch. (Basic pump kits include: pump, idler pulley, clutch, serpentine belt, crankshaft pulley, pump mtg. Bracket's as needed.
Buyers Products R38DR Series Control Cable with 3 Inch Travel and Rod End
Control is designed for heavier applications. The cable is built to last with
a rust-resistant stainless steel core, and long lay construction. Replaceable
control knob included.
Order nuts and washers separately. For bulkhead applications order the BNW015
Control Cable Nut and Washer Kit.
This is a Parker 17 Gallon Per Minute Hydraulic Pump at 1600 RPMs. This is a
Parker PH14 "A" Mount Pump with a clockwise rotation. This pump features side
ports. This pump has a 7/8" tapered shaft with a woodruff keyway. This pump
will work with Chevron Wreckers.
DewEze Clutch Pump Mount Kit for 1999-2003 Ford 7.3L Side Port A Pump. Hydraulic Power System by
DEWEZE MANUFACTURING. Mobile Hydraulic Power for Trucks and Vans. Instant
Hydraulic Power with the Flip of a Switch!
(Basic pump kits include: pump, idler pulley, clutch, serpentine belt, crankshaft pulley, pump mtg. Bracket's as needed.
This PTO Cable Mount Kit from Muncie is for low friction PTO Cables, single
gear Muncie PTO's and some Chelsea PTO's. It is also for 1/4"-28 thd and
5/16"-24 thd Control Cables.
DewEze Clutch Pump Kit (Basic Pump Kits Include: Pump, Idler Pulley, Clutch
Serpentine Belt, Crankshaft Pulley, Pump Mtg. Bracket) For 2003 to and
Including 2010 Chevrolet or GMC 4500/5500 Series Chassis With 8.1 Gas Engine.
For use on trucks with Single Alternator with A/C.
This Hydraulic Fitting Connector from Miller Industries measures 3/8" MJ x 1/2"
MB. It is used on the Hydraulics Assembly of several Miller Car Carriers. These
Carriers include Century, Challenger, Champion, Holmes, and Vulcan. See the
features below for a full list of carriers and see the brochure tab for
breakdowns.
DewEze A Clutch Pump Kit Ford 2011-2024 6.7L for diesel fuel. Dual alternator truck only (Must take second alternator off and get re-programmed at Ford Dealership (Basic Pump Kits Include: pump, idler pulley, clutch, serpentine belt, crankshaft pulley, pump mtg. Bracket's as needed).
DewEze A Clutch Pump Kit For 2012 to 2024 and including 2016 Ford Series Chassis with 6.7L diesel engine. Requires
removal of one alternator. (Basic Pump Kits Include: pump, idler pulley, clutch, serpentine belt, crankshaft pulley, pump mtg. Bracket's as needed).
DewEze Clutch pump mount kit for V-10 Ford 2008 to 2016 Ford
V-10 w/o spider. mobile hydraulic power for trucks and vans. Instant hydraulic
power with the flip of a switch!
(Basic pump kits include: pump, idler pulley, clutch, serpentine belt, crankshaft pulley, pump mtg. Bracket's as needed.
Adjust the throttle for your PTO from inside the cab with this covered cable
from Buyers Products. Pull the handle out until you've reached the desired
idle, and then turn 90? to the right to lock it. Reverse the procedure to
release.
DewEze Warner clutch #1417-24 6-groove AA mount
BURNISHING-TO AVOID BURNING OR HEAT DISTORTION, THE FOLLOWING PROCEDURE IS RECOMMENDED: After clutch is installed, run at 1000-1200 RPM. Cycle the clutch on/off at the rate of 10 seconds on - 10 seconds off for a minimum of 50-100 cycles